Efficient photocatalytic hydrogen evolution with ligand engineered all-inorganic InP and InP/ZnS colloidal quantum dots

Shan Yu1,2, Xiang-Bing Fan3, Xian Wang 4, Jingguo Li2, Qian Zhang1,2, Andong Xia 4, Shiqian Wei1 , Li-Zhu Wu 3, Ying Zhou 1 & Greta R. Patzke 2

DOI: 10.1038/s41467-018-06294-y

Photocatalytic hydrogen evolution is a promising technique for the direct conversion of solar energy into chemical fuels. Colloidal quantum dots with tunable band gap and versatile surface properties remain among the most prominent targets in photocatalysis despite their frequent toxicity, which is detrimental for environmentally friendly technological implementations. In the present work, all-inorganic sulfide-capped InP and InP/ZnS quantum dots are introduced as competitive and far less toxic alternatives for photocatalytic hydrogen evolution in aqueous solution, reaching turnover numbers up to 128,000 based on quantum dots with a maximum internal quantum yield of 31%. In addition to the favorable band gap of InP quantum dots, in-depth studies show that the high efficiency also arises from successful ligand engineering with sulfide ions. Due to their small size and outstanding hole capture properties, sulfide ions effectively extract holes from quantum dots for exciton separation and decrease the physical and electrical barriers for charge transfer.

Conversion of solar energy into storable hydrogen fuel through water splitting is one of the most sustainable solutions to meet the increasing worldwide energy demands1,2. Among the wide spectrum of photosensitizer types that has emerged over the past years3–8, colloidal quantum dots (QDs) stand out through combining molecular versatility with the efficient light harvesting properties of semiconductors9,10, and facile charge carrier transport through interfaces10,11. Photocatalytic processes with semiconductor nanomaterials and QDs12,13, such as CdS, do not only provide most direct low-tech access to clean hydrogen, but also permit fundamentally new insight into the photophysics of hydrogen production14. CdS/ CdOx QDs furthermore open up new avenues for solar photoreforming of lignocellulose biomass to hydrogen15. To date, Cdchalcogen II–IV QDs remain the most efficient QD types in photocatalytic systems15–20. However, the toxicity of Cd severely limits their large-scale application options, not only in photocatalytic water splitting, but also in other urgent global challenges, such as water disinfection21 and the elimination of multidrugresistant bacteria22 with photoexcited QDs. This current need for efficient non-toxic QDs has brought forward complex engineering approaches towards multinary I–III–VI2 and I2–II–IV–VI4 nanoscale semiconductors23

InP QDs are an attractive alternative target for direct solar-tofuel conversion. Furthermore, InP is well suited for environmental and biological applications24, and the notably lower toxicity of InP/ZnS QDs compared to CdSe/ZnS QDs has recently been demonstrated both in vitro and in vivo25. Surprisingly, however, InP QDs have rarely been studied for their artificial photosynthesis properties, although InP nanomaterials were used in breakthrough photoelectrode and solar cell studies26,27. In comparison to the most widely investigated CdSe QDs, InP has a smaller bulk band gap (1.35 eV vs 1.76 eV) and larger Bohr exciton radius (9.6 nm vs 4.6 nm), which widens its corresponding absorption and emission range. In addition, InP displays a more evident extent of covalent bonding than CdSe, leading to higher delocalization of wavefunctions and weaker attraction between electrons and holes, as well as weaker phonon coupling24.

Here we show the potential of InP QDs as hydrogen evolution photosensitizers. Inspired by recent synthetic developments28, we access a series of InP and InP/ZnS QDs using economic and safe (dialkylamino)phosphines as phosphorus source. Modification of the as prepared QDs with inorganic sulfide (S2-) ions29,30 furthermore brings forward progress in ligand engineering of QDs, as a key area in solar energy conversion31. These sulfide ions not only endow QDs with good water solubility, but also with remarkable activity in photocatalytic processes32. We demonstrate the important role of S2− ligands for photocatalytic hydrogen evolution by comparing different organic and inorganic ligand types. S2− ligands not only effectively facilitate the extraction of photogenerated holes from the QDs to the surface ligands, but also decrease the charge transfer barriers between QDs and their surrounding acceptors, thus notably enhancing photocatalytic hydrogen evolution.

Results

Synthesis and characterization. InP and InP/ZnS colloidal QDs were synthesized based on a modified literature protocol (see Supplementary Fig. 1 for photographs)28,33. First, the size of the QDs was adjusted by tuning the ratio of ZnCl2 to ZnI2, instead of introducing of different indium halides. Furthermore, the growth temperature for ZnS was directly held constant at a higher value prior to the addition of sulfur (cf. Methods, Supplementary Method 1 and Supplementary Note 1 for further information). The characteristic absorption peak of the QDs undergoes a blue shift from 570 nm to 435 nm upon increasing the ratio of ZnI2 to ZnCl2 in the system (Fig. 1a). Likewise, the emission peak of InP/ ZnS QDs is shifted from 605 nm to 515 nm (Fig. 1b). The typical emission spectra of the as-synthesized InP/ZnS QDs exhibit FWHM (full width at half maximum) values around 60 nm, close to the reported optimal results33–35. While coating of InP QDs with ZnS barely changes the absorption spectrum of the original InP QDs, it leads to a significant improvement of the photoluminescence quantum yield (PLQY) of the system from 1.0 to 46% with increasing growth time of the capping layer (Supplementary Fig. 2). This confirms that the growth of ZnS on QDs efficiently passivates their surfaces36.

Ligand exchange was then carried out to replace the original long-chain organic ligands (oleylamine, OLA) on the surface of the QDs (referred to QDs-OLA) with inorganic S2- (referred to QDs-S; cf. Methods for details)30. The success of this process is evident from the efficient phase transfer of the treated QDs from hexane to N-Methylformamide (NMF) (inset of Fig. 1c). These S2- capped QDs could be well dissolved in water by further precipitation and redispersion, in line with their sufficiently negative zeta potential (Supplementary Fig. 3). The excitonic features in the absorption spectra remain constant after ligand exchange, implying that the size changes of the QDs are negligible after sulfide capping (Fig. 1c and Supplementary Fig. 4)30,37. Nevertheless, the PLQY of InP/ZnS QDs after ligand exchange dropped drastically (Fig. 1c) due to the increased amount of surface traps and nonradiative relaxation processes38,39. Efficient ligand exchange is furthermore evident from the almost complete disappearance of the ligand C-H stretching FT-IR bands at 2855 and 2924 cm−1 (Fig. 1d)29,30. In addition, thermogravimetric analysis (TGA) of S2− capped QDs shows no obvious weight loss between 100 and 500 °C in contrast to ligand loss of OLA capped QDs (Supplementary Fig. 5), thus providing further evidence for the removal of most organic ligands29,37.

TEM and HRTEM images indicate a typical narrow size distribution of the InP QDs (525 nm) with an average size around 2.7 nm, which is close to literature data28. After growth of ZnS for 15 min, the size of QDs changed slightly (Supplementary Figs. 6 and 8). After ligand exchange, the shape and size of InP and InP/ ZnS QDs did not change obviously (Supplementary Figs. 7 and 8), although a slight degree of aggregation took place due to the less repulsive effect of inorganic sulfide ions compared to longchain organic molecules. Due to the very thin ZnS layer and the small size of QDs, the direct assignment of ZnS based on lattice planes or EDS elemental mapping is difficult. However, a less crystalline zone outside the InP core in the aberration-corrected STEM image (Supplementary Fig. 9) may arise from the surface modification of QDs with such a thin ZnS layer40. Powder X-ray diffraction (PXRD) data (Supplementary Fig. 10) confirm that the zinc blende structure of the QDs is maintained during both ZnS growth and ligand exchange processes, accompanied by a peak shift to higher angles from InP QDs to InP/ZnS QDs28,35. Elemental analyses by inductively coupled plasma optical emission spectrometry (ICP-OES, Supplementary Table 1) and energy-dispersive X-ray spectroscopy (SEM-EDS, Supplementary Table 2) both show that ZnS growth on InP QDs within 15 min is slow under the applied synthetic conditions, according to the low Zn/In atomic ratio in the QDs. Generally speaking, the notable lattice mismatch (7.7%) of ZnS and InP renders the growth of thick ZnS layers difficult36. Although ZnS layers obtained from longer reaction times would improve the PLQY of QDs (Supplementary Fig. 2b)28, it may not be an optimal choice for photocatalysis (see below). In addition, the sulfur content in the composites after ligand exchange increased obviously, which is in line with the above analysis.

Fig. 1 Spectroscopic characterization of InP and InP/ZnS QDs. a Absorption spectra of different InP and InP/ZnS (15 min) QDs in hexane. b PL spectra of different InP/ZnS (15 min) QDs in hexane. c Absorption spectra and PL spectra before and after ligand exchange for InP/ZnS QDs (525 nm, 15 min) in hexane and water (the absorbance of the two QD types was adjusted to the same value at the excitation wavelength to enable PL comparison). d FT-IR spectra of QDs before and after ligand exchange.

Photocatalytic hydrogen evolution. After the concentration of the colloidal solution was determined (cf. Supplementary Method 2), InP-S and InP/ZnS-S QDs were tested for hydrogen evolution in the presence of ascorbic acid (H2A) as electron donor and Ni2+ as proton reduction catalyst, along the lines of the reported assays for Cd-based QDs17,41. Control experiments show that light, photoabsorber QDs, the electron donor H2A, and the Ni2+ catalyst are all indispensable for efficient hydrogen evolution (Fig. 2a), and the optimal concentration of Ni2+ and H2A as well as the optimal pH for the present system were studied (Supplementary Fig. 11). Moreover, we compared the photocatalytic performance with pristine InP-S QDs (525 nm) with two conventional CdSe-S QD batches from different protocols (with similar absorption peak, size, and ligand exchange procedures) under analogous conditions (see Supplementary Method 3). The results show that the hydrogen generation efficiency of InP QDs is even higher than that of CdSe QDs (Fig. 2b). This demonstrates that InP-based QDs bear a high potential for photocatalytic hydrogen evolution with environmentally friendly materials. Furthermore, the overall photocatalytic hydrogen evolution efficiency was enhanced after the growth of ZnS layers on InP QDs (Supplementary Fig. 12). In particular, InP/ZnS QDs with a ZnS growth time of 15 min (with a thin ZnS layer, see results above) outperform the other samples. As ZnS has a higher conduction band and a lower valence band, a type I heterostructure is formed between InP and ZnS. Therefore, electrons and holes tend to localize in InP. Although ZnS can decrease the concentration of some intrinsic surface defects, extraction of the photogenerated charges by Ni2+ and H2A would be less efficient in case of a thick ZnS layer42, which is in sharp contrast to the requirements for high PLQY. Moreover, hydrogen evolution was evaluated for InP and InP/ZnS QDs with different excitonic absorption peaks under illumination with an AM 1.5 solar simulator (Fig. 2c), and all of them exhibited good performance. This may result from their optimal band gap settings, which ensure both efficient absorption of the incident light from the solar simulator and the sufficient driving force for photogenerated charge transfer and subsequent reactions.

Under optimal conditions, photocatalytic hydrogen evolution was performed with different light sources (Supplementary Fig. 13). The hydrogen generation rate for the system reaches 45 mmol h−1 g−1 within 64.5 h (see Supplementary Fig. 13a and Supplementary Method 4) with a LED light source, and the TON value is as high as 128,000 based on InP/ZnS-S QDs (and 5900 normalized to Ni centers). The apparent quantum yield (AQY) of the system correlates well with the absorption spectra of InP/ZnS QDs, and the internal quantum yield (IQY) reaches 31% at 525 nm (Supplementary Method 5, Supplementary Table 3 and Supplementary Fig. 14). When using an AM 1.5 solar simulator as an alternative light source, the TON and hydrogen evolution rate within 20 h are 61,500 and 70 mmol h −1 g−1, respectively (Supplementary Fig. 13b). Online photocatalytic hydrogen evolution tests show that InP/ZnS-S QD systems display long-term activity over 100 h (Fig. 2d). PXRD patterns further confirm that the diffraction peaks of QDs are still distinguishable after evolution of 0.65 mmol H2 (Supplementary Fig. 15). The decline of the hydrogen evolution rate after long time irradiation may be caused by the accumulation of the oxidation product dehydroascorbic acid (DHA)43, as well as by partial degradation of the QDs. However, the total amount of H2 production is satisfactory and competitive in all of the investigated reaction conditions. The above results in their entirety clearly highlight S2− capped InP and InP/ZnS QDs as a promising photosensitizer type.

Fig. 2 Photocatalytic hydrogen evolution experiments. a Amount of hydrogen evolved from reference systems without Ni2+, H2A, QDs or light illumination, respectively. b Comparison of hydrogen evolution results with InP-S QDs (525 nm) and two types of CdSe-S QDs (~525 nm). c Hydrogen evolution with InP-S QDs and InP/ZnS-S QDs (abbreviated as IZ) with different excitonic absorption peaks. d Long time hydrogen evolution of InP/ZnS-S QDs (shadowed area: error range). Conditions: a 1.6 μM InP/ZnS QDs, b 1.6 μM InP-S QDs (525 nm) and CdSe-S QDs with the same absorbance at 525 nm or c 2 μmol (of molecular concentration) QDs with different absorption peak, with 0.035 mM Ni2+ in 6 mL of 0.2 M H2A (pH 4.5) were illuminated with a, b LED light source (525 nm, 4 × 1 W) and c AM 1.5 simulator light; d 1.9 μM QDs (525 nm, 15 min) and 0.042 mM Ni2+ in 10 mL of 0.2 M H2A (pH 4.5) with LED light source (453 nm, 0.23 W). Error bars were estimated based on the standard deviation according to two or more independent experiments

Photophysical study of the system.

To study the mechanisms behind the photocatalytic process, the thermodynamic properties of InP/ZnS QDs were first evaluated. The conduction and valence band edge positions of InP/ZnS QDs were determined as −0.92 V and 1.35 V (vs NHE) through cyclic voltammetry (CV) measurements (Supplementary Fig. 16)44, in line with other reports26. Given the standard redox potentials of Ni2+/Ni (−0.25 V vs NHE) and H2A/DHA (0.36 V vs NHE)41,45, electron transfer from QDs to Ni2+ and hole transfer from QDs to H2A thus appears feasible. DHA hydrate is the main oxidation product of H2A after photocatalysis, which was verified through 13C NMR spectroscopy (Supplementary Fig. 17). However, the formation of metallic Ni was not detected by EPR spectroscopy of the present system after illumination (Supplementary Fig. 18), in line with some other reports17,46. In addition, no significant absorption changes were observed and the zeta potential of the system remained sufficiently negative at pH 4.5 (cf. Supplementary Fig. 19, Supplementary Note 2, and Supplementary Table 4). This indicates that the majority of the S2− ligands on the QDs are retained under the photocatalytic conditions.

Time-resolved spectroscopy was then performed to obtain direct insight into the photophysical behavior of charge carriers. Femtosecond transient absorption (fs-TA) experiments were firstly conducted using a home-built femtosecond broadband pump-probe setup with time resolution around 100 fs as described previously in detail47. Concentrations of samples were adjusted to an absorbance of 0.3 OD at a pumping wavelength of 480 nm in 1 mm pathlength quartz cuvettes, and continuous stirring was performed during the test to alleviate photodegradation. The TA spectra (Fig. 3a, b) display two prominent features, namely a typical excitation bleaching (XB) and a featureless broad photoinduced absorption (PA). The XB signal is usually attributed to the state filling of the 1 S electron level in the conduction band, as state filling of the 1 S hole level is often negligible due to a higher density and degeneracy of the hole levels in QDs48,49. In contrast, both electrons and holes can be responsible for the PA signal, and it may vary with different QDs and surface states49,50. We here analyzed the origin of PA in the present system with respect to two aspects. One is the different decay behavior for the kinetics for XB and PA (Supplementary Fig. 20). This means that the species contributing to PA differs from that responsible for XB50. The other strategy is the analysis of the kinetic changes after H2A and Ni2+ were introduced (Fig. 3d)49,51. When the electron donor H2A is added, the decay of PA becomes faster, while no obvious changes occur after addition of Ni2+. Therefore, we attribute the PA signals mostly to the holes in InP/ZnS QDs.

Based on this analysis, we further compared the kinetics for the XB (Supplementary Fig. 21a) and PA (Fig. 3c) signals of both InP/ ZnS-OLA QDs and InP/ZnS-S QDs, respectively. For InP/ZnSOLA QDs, the decay of TA signal is slow, indicating that the trap state within the QDs is suppressed, in line with their bright luminescence. After ligand exchange of OLA by S2−, both XB and PA decay become faster. Usually, S2− ligands can act as hole traps above the valence band38,52. Although the hole transfer to S2− seemingly should not affect the kinetics of XB, the faster recovery of XB is not surprising (Supplementary Fig. 21a), given that there are numerous works reporting that the hole transfer process indeed leads to a faster decay of XB, which is still subject to discussions53–55. In contrast, the faster decay of the PA signal for holes in InP/ZnS-S QDs can be clearly explained with the hole transfer process (Fig. 3c). Other than OLA, the S2− ligands on the surface accept photogenerated holes from QDs, thus providing an additional pathway for hole extinction, which accelerates the disappearance of the hole related transient PA signal. Fitting of PA signal kinetics clearly illustrates that an additional decay process with a timescale around 110 ps appears for InP/ZnS-S QDs in comparison to InP/ZnS-OLA (Supplementary Table 5), which is consistent with the hole transfer process from QDs to S2− ligands.

Fig. 3 fs-TA spectra of InP/ZnS QDs (525 nm, 15 min). a TA spectra of InP/ZnS-OLA QDs; b TA spectra of InP/ZnS-S QDs at indicated delay time windows. c TA kinetics at 725 nm (average from 700 nm to 750 nm) for the PA signal and the corresponding fitting curve of InP/ZnS-OLA and InP/ZnS-S QDs. d TA kinetics at 725 nm (average from 700 nm to 750 nm) for the PA signal of InP/ZnS-S QDs with and without introduction of H2A or Ni2+ into the solution. Conditions: pump pulses wavelength: 480 nm.

Moreover, comparison of the kinetic decay of InP/ZnS-S QDs in the presence/absence of Ni2+ or H2A demonstrates that charge transfer proceeds on the ps scale in the system. On the one hand, hole transfer is evident from the faster decay of the PA signal after the introduction of H2A into the solution (Fig. 3d); and on the other hand, electron transfer from QDs to Ni2+ is observable as well from the faster recovery of the XB electron signal after the addition of Ni2+catalyst (Supplementary Fig. 21b)49,56.

Due to the limited timescale of the fs-TA experiment (up to 1 ns), further information about the charge transfer processes on the nanosecond scale was obtained from steady-state and timeresolved emission spectra of InP/ZnS-S QDs. The emission of the QDs was quenched notably after introduction of small amounts of Ni2+ and H2A into the system, and this effect increased gradually with higher amounts (Fig. 4a, b). The kinetic emission decay of the QDs became faster as well, in line with the decrease of emission intensity (Fig. 4c, d). Fitting results show that the average lifetime of InP/ZnS QDs dropped from 37.0 ns to 17.7 ns and from 38.2 ns to 2.52 ns with Ni2+ and H2A concentrations of 0.04 mM and 3 mM, respectively (see Supplementary Tables 6 and 7 and Supplementary Method 6). This points to a calculated electron transfer rate from QDs to Ni2+ of 7.64 × 108 s−1 mM−1 and a hole transfer rate from QDs to H2A of 1.25 × 108 s−1 mM−1 (inset of Fig. 4c, d).

Significance of sulfide capping. The above analysis indicates that the surface S2− ligands influence the photophysical processes of QDs, which may also contribute to the high hydrogen evolution performance of the present system. We thus further explored the role of surface sulfide ligands beyond their endowing QDs with water solubility. To that end, we systematically compared InP/ ZnS-S QDs to a series of QDs capped with other ligands with respect to their respective activity in photocatalytic hydrogen evolution. The ligands were selected with respect to two criteria. First the ligand exchange process should be easy and efficient, and secondly the ligands should stabilize InP and InP/ZnS QDs as colloids in solution.

Usually, colloidal QDs synthesized in organic phases are capped with oil-soluble long alkyl chains (OLA in the present case), and the conventional ligands used to transfer QDs from nonpolar solvents to water are organic thiols. We thus prepared InP/ZnS QDs capped with 3-mercaptopropionic acid (MPA) and 11-mercaptoundecanoic acid (MUA) by similar ligand exchange methods (named as InP/ZnS-MPA and InP/ZnS-MUA QDs, details in Supplementary Method 7), which are two widely used organic thiols for ligand exchange. Interestingly, the hydrogen evolution efficiency with these two QD types is considerably below that of InP/ZnS-S QDs (Fig. 5a). Similar phenomena have been observed in field effect transistors and in solar cells based on QDs with inorganic ligands over the past years30,31,57,58. Recent work also shows the inhibitory effect of thiol ligands on CdS QDs for photocatalysis59, and exceptional hydrogen evolution efficiency was achieved based on CdSe/CdS QDs with S2− ligands32. So here we attribute the superior hydrogen evolution efficiency with InP/ZnS-S QDs to the replacement of conventional organic ligands by inorganic sulfide ligands.

Fig. 4 Steady state and time-resolved photoluminescence quenching experiment of InP/ZnS-S QDs (525 nm, 15 min). a, b Static photoluminescence quenching for InP/ZnS-S QDs in water after addition of different amounts of Ni2+ and H2A. c, d PL decay curves of InP/ZnS-S QDs after addition of different amounts of Ni2+ and H2A respectively; the inset shows the fitting curve for lifetime changes with increased concentration of Ni2+/H2A. Conditions: pH of all solutions was adjusted to 4.5; excitation wavelength: 406 nm.

Transient photocurrent measurements (Fig. 5b) show that InP/ ZnS-OLA QDs barely respond to light. In contrast, InP/ZnS-MPA QDs and InP/ZnS-S QDs displayed a quick light response. Especially InP/ZnS-S QDs exhibited a higher current density than InP/ZnS-MPA QDs, i.e., InP/ZnS-S QDs exhibit favorable interaction with their reaction system. Additionally, electrochemical impedance spectroscopy (EIS) data show that FTO electrodes covered with InP/ZnS-S QDs exhibit the lowest resistance under light illumination among the test series (Fig. 5c). Fitting results indicated that Rct was 2.3 × 104, 7.8 × 104, 1.4 × 106, and 6.2 × 105 Ω for FTO covered with InP/ZnS-S, -MPA, -OLA QDs and blank FTO, respectively (see Supplementary Fig. 22 and Supplementary Table 8). Note that the Rct of InP/ZnS-OLA QDs even exceeds the blank value, thereby indicating that organic ligands inhibit charge transportation. Alternatively, InP/ZnS-S QDs may display more active interfaces compared to InP/ZnS-MPA QDs. Compared to organic ligands, such as OLA and MPA, the single anion S2− can far more easily circumvent the physical and electrical barriers arising from the large volume and insulator carbon chains of organic ligands58,60,61. This may facilitate the migration of charge carriers from the QDs towards other components of the reaction systems, in particular H2A or Ni2+. Additionally, this may be the reason why InP/ZnS-MPA QDs are much better photosensitizers than InP/ZnS-MUA QDs, given that the carbon chain of MPA (3) is shorter than that of MUA (11).

After confirming the superior activity of sulfide ligands over organic thiol ligands in the present system for hydrogen evolution, we furthermore synthesized InP/ZnS QDs capped with Cl− and PO4 3− (denoted as InP/ZnS-Cl and InP/ZnS-PO4 QDs, details in Supplementary Method 8) to explore possible differences between InP/ZnS-S QDs and those with other inorganic ligands. Interestingly, the hydrogen evolution efficiency in the presence of these QDs was also much lower than that of InP/ZnS-S QDs (Fig. 5d and Supplementary Fig. 23 for InP QDs). In combination with the above results, we tentatively attribute this to the effective hole transfer from the intrinsic QDs to sulfide, which is more difficult for chloride and phosphide due to their relatively positive oxidation potential.

Electron paramagnetic resonance (EPR) spectroscopy was then performed to obtain further information on the different allinorganic QD types. As shown in Fig. 5e and Supplementary Fig. 24, no obvious signals could be observed for all QDs in the dark. With light on, still no obvious signal was recorded for InP/ ZnS-Cl and -PO4 QDs. However, for InP/ZnS-S QDs, a signal around a g factor of 2.006 immediately emerges after light irradiation. The absence of this signal in the dark indicates that it is highly related to the photogenerated exciton, rather than to the intrinsic structure defects or surface states of the QDs62. Careful examination further shows that it does not arise from photogenerated holes in InP QDs (g = 2.001)62,63. Instead, it is probably due to electrons in the conduction bands of InP QDs (g = 2.006) according to the relevant literature62,63. This hypothesis was further confirmed by control experiments: after the introduction of H2A into the system to deplete the photogenerated holes, this signal became much more evident (Supplementary Fig. 24). As all the QDs in our test are derivatives of InP/ZnSOLA QDs, their interior exciton processes should be similar. We therefore believe that this electron related signal in our system is directly related to the hole capture ability of the surface ligands.

Fig. 5 Influence of different ligands on the hydrogen evolution performance and photophysical properties of InP/ZnS QDs (525 nm, 15 min). a Hydrogen evolution for InP/ZnS QDs capped with different organic ligands. Conditions: 1.6 μM QDs and 0.035 mM Ni2+ in 6 mL of 0.2 M H2A (pH 4.5) were illuminated with a LED light source (525 nm, 4 × 1 W). b Transient photocurrent and c electrochemical impedance spectra of InP/ZnS QDs with different ligands at open circuit voltage under simulated sunlight illumination. Conditions: electrolyte: 0.2 M H2A, pH 4.5; frequency range: 0.1–105 Hz. d Hydrogen evolution for InP/ZnS QDs capped with different inorganic ligands. Conditions: 1.6 μM QDs and 0.035 mM Ni2+ in 6 mL of 0.2 M H2A (pH 4.5) were illuminated with a LED light source (525 nm, 4 × 1 W). e EPR spectra for InP/ZnS QDs with different ligands. The magnetic field intensity was transformed into g factor values. f SPV spectra for InP/ZnS QDs capped with different ligands. Xe lamp was used for irradiation. Error bars were estimated based on the standard deviation according to three independent experiments.

Accordingly, we conclude that holes in InP/ZnS-S QDs effectively transfer from the interior to surface S2−, which in return significantly increases the stability of electrons in the conducting band and renders them detectable in the EPR spectra at room temperature. As a contrast, the hole transfer from QDs to Cl− or PO4 3− is limited and the relevant signals are not obvious (Fig. 5e).

Moreover, surface photovoltage spectra (SPV) of InP/ZnS-S, -OLA, -MPA, and -Cl QDs were recorded to obtain more information about different charge separation and transportation characteristics of S2− capped QDs compared to those equipped with other typical organic and inorganic ligands. No photovoltage existed beyond 600 nm for QDs, and this is in accordance with the absorption spectrum of QDs, meaning that no sub-band gap excitation from the trapped state contributes to the photogenerated charge transfer process64. The corresponding photovoltage generated by -S QDs is obviously much larger than that of -OLA, -Cl, and -MPA QDs (Fig. 5f), confirming the efficient charge separation of the sulfide capped particles once again65. The positive response means that positive charge accumulated at the interface under irradiation66, further demonstrating that sulfide ligands extract holes to the surface of InP/ZnS-S QDs, in line with the above TA and EPR experiments. Besides, strong interdot coupling and band-like charge transport may exist in QDs capped with inorganic ligands, such as S2− or Cl−30,67, which could contribute to their higher charge mobility and resulting higher photovoltage in contrast to MPA and OLA capped QDs.

Furthermore, density functional theory (DFT) calculations (Supplementary Method 1, Supplementary Figs. 25–27, and Supplementary Note 3) also indicate that introduction of S centers on the surface of the QDs is beneficial for charge transfer, which is consistent with the above experiments and analyses. Moreover, the nature of S2− ligands is different from the intrinsic defects on InP QDs, and the latter can be suppressed by the introduction of ZnS.

Discussion

As the surface S2− ligands may be regarded as a kind of surface trap, which is indicated by the decrease of the QD luminescence, we further analyze the different role of S2− ligands compared to the ordinary intrinsic defects of QDs according to the above experimental measurements and theoretical calculations (Supplementary Fig. 28). The ordinary intrinsic defects on QDs are often disordered, and they always act as recombination centers for holes and electrons, which both lowers the band-edge emission of QDs and reduces the charge separation efficiency68. In our work, the introduction of ZnS on InP QDs can be considered as a suitable strategy to decrease the amount of intrinsic defects which are detrimental for photocatalysis with QDs. The effectiveness of this approach is proven by the higher PLQY and hydrogen evolution efficiency after ZnS layer growth. Alternatively, the introduction of S2− ligands can be regarded as an exterior trap69. Although the surface S2− ligands decrease the emission of QDs in the present case, they improve the charge separation efficiency of the system because of their hole capture ability. That is, after light excitation of QDs, the holes can transfer quickly to the S2− ligands, which is beneficial for electron/hole separation. Moreover, the small volume of S2− in comparison to the traditional organic ligands lowers the barrier for further hole transfer from S2− to H2A.

In summary, we have successfully introduced inorganic S2− capped InP and InP/ZnS QDs as efficient photosensitizers for hydrogen evolution. InP/ZnS QDs reach TON values up to 128,000 per QDs and an internal quantum yield of 31% (525 nm). This demonstrates the remarkable potential of S2− capped InPbased QDs for photocatalytic applications. Moreover, using a series of spectroscopic and photoelectrochemical characterizations, we demonstrate that inorganic sulfide ligands on QDs are beneficial for the photocatalytic hydrogen evolution. In comparison with conventional organic ligands and other inorganic ligands, sulfide ions on the surface can extract the holes from the interior of QDs rapidly, followed by their reaction with H2A via low physical and electronic barriers. This leads to efficient charge separation and notably enhances the photocatalytic hydrogen evolution performance. Key perspectives for further progress are the development of other InP-based heterostructures, and the application of inorganic sulfide capped InP QDs for a wider spectrum of photocatalytic reactions.